Unimark Machines Pvt Ltd Dhantoli, Nagpur, Maharashtra

We are offering airless paint machine. the unimark upa500 truck-mounted airless paint machine is equipped with twin 9-liter 3,000 psi paint pumps supplying automatic paint. Continuous cycle road markings from twin hydraulic agitated paint tanks. Capacities from 200 to 500 liter twin tanks for yellow or white line marking. 11-programme automatic linegap control with semi-automatic or manual plus line totalising. Pressurised glass bead system for surface application if required for immediate retroreflectivity. Hot paint application also available. High output spray guns for high volume marking. Optional sun canopy for hot climates. the upa500 can be supplied with 3 spray guns for airport runway marking. Hot paint is achieved by passing paint through a water heat exchanger for temperatures up to 80 degrees centigrade

The Unirib machine is an economical solution to small patching or raised profiles. It is bucket-fed and used similarly to a hand mold. Weighing only 50kg, the machine is light enough to load onto a truck. Application is by hand control and sight bar. The unit is supplied with a glass bead dispenser and can also be automated in a manner similar to the hand-propelled line machine.       Unimark operates on policy of continual research and development, therefore specifications can change without notice. The images are indicative.  

Engine Kohler 13 HP vertical single cylinder gasoline engine. Smart choke easy start system. More than enough power to remove profile markings in one pass. Transmission Twin section vee belts to isolate engine shaft from shock. Grinder Triple off-set spoke vertical drive axle with twin sealed bearings. 3-off rotating cutter segments with 18-off tungsten carbie cutters on each segment. 2-off sealed bearing units in each cutter. Dust suppression rubber skirt around cutter unit. Control Cutter lowering lever mounted on handle bar. Fine depth control mounted on cutter chassis easily reached from operating position. Fine cut control for smooth finish without damage to asphalt. Chassis Sturdy 80 x 40mm steel section with 2-off 200mm dia. wheels at front and 2-off 150mm dia. castors at rear. Safety Engine speed control and off switch mounted at right hand. Cutter lower/raise mounted at left hand. Foot parking lever raises machine at rear and prevents movement. Handle bars on anti-vibration rubber units.

We offer thermoplastic pedestrian crossing machine. The unimark pedestrian crossing machine is a hand pull machine applying screed thermoplastic panels in widths according to individual specification but typically 50 cm wide. The propane gas heated tank will apply one panel per fill at 3 mm thick. An adjustable glass bead dispenser is fitted for instant retroreflectivity. The machine is designed to give very neat single application panels for a professional finish to pedestrian crossings.

The Unimark Pedestrian Crossing Machine is a hand pull machine applying screed thermoplastic panels in widths according to individual specification but typically 50 cm wide. The propane gas heated tank will apply one panel per fill at 3 mm thick. An adjustable glass bead dispenser is fitted for instant retroreflectivity. The machine is designed to give very neat single application panels for a professional finish to pedestrian crossings.   Unimark operates on policy of continual research and development, therefore specifications can change without notice. The images are indicative.

We are offering unimark construction profiler. The unimark hand-propelled profile line machine has been developed for small patching works where it is not cost-effective to use large plant, or for situations in which contractors do not require the capital outlay of larger plant. The machine is very maneuverable and lightweight, but a very sturdy construction. the machine comes complete with profile shoe, glass bead dispenser, propane tank heater, delivery tube heater and twin profile shoe heaters fitted with our unique rotary connection for quick change of laying shoe and following of road countour changes. with its tank capacity of 65 liters, approximately 85 meters of 200mm line per fill is available. The standard cam will apply 250mm and 500mm ctrs, but can be modified to suit your requirements.

The Unimark hand-propelled profile line machine has been developed for small patching works where it is not cost-effective to use large plant, or for situations in which contractors do not require the capital outlay of larger plant. The machine is very manouvreable and lightweight, but a very sturdy construction. The machine comes complete with profile shoe, glass bead dispenser, propane tank heater, delivery tube heater and twin profile shoe heaters fitted with our unique rotary connection for quick change of laying shoe and following of road countour changes.

We are offering the unimark hand propelled primer application machine is lightweight and easy to use. Designed for applying primers to concrete or worn asphalt prior to thermoplastic line application. The machine has a spray nozzle which is supplied from a hand pump pressurizing the primer tank. As with all unimark equipment attention has been paid to simplicity of use and robust design.

The Unimark Hand Propelled Primer Application Machine is lightweight and easy to use. Designed for applying primers to concrete or worn asphalt prior to thermoplastic line application. The machine has a spray nozzle which is supplied from a hand pump pressurising the primer tank. As with all Unimark equipment attention has been paid to simplicity of use and robust design.   Unimark operates on policy of continual research and development, therefore specifications can change without notice. The images are indicative.

We are offering unimark hymix vertical preheater. All unimark vertical preheaters are supplied with powerful hydraulic motor driven agitators, with the pump driven by electric start diesel engines. The base mounting allows easy fitting to any vehicle or trailer. The burner system is designed to give very fast heat up time and is controlled by our electronic gas management system with thermostat, auto-ignition and flame-out protection. Economical in use with full wrap round insulation which also gives operator protection.supplied as single or twin units ranging from 90 to 630 liters per single unit and with direct flame or indirect oil jacket heating. 12 v diesel oil burner systems can also be supplied if preferred. Built on a larger gvw truck, usually 17 tonnes and with the addition of twin preheaters this machine gives the contractor the advantage of using only one truck. The machine has the capacity to leave the depot laden with up to 6-tonnes of thermoplastic and smaller pickup trucks can feed it throughout the day for major lining works. The machine can be supplied with all variations or application equipment and accessories.

We are offering hot compressed air trolley dryer. The unidry converts compressed air to high-velocity air over the venturi, where the gas is introduced, making a high-velocity mixture in our renowned nickel alloy dryer head. Internal combustion allows heated air to exit at very high temperature. The air is produced from our own turbine compressor, which is light enough to be manually pushed on the machine. Ignition is from out high-performance auto-spark generator. Can be platform-mounted for fitting to existing road marking vehicles.

We are offering the unimark cold applied plastic machine has been specially designed to apply cold curing plastic materials in a number of application systems, specifically raised profiles, agglomerates (textured) and screeded lines. The machine will apply material from a premixed drum of material with simple to use controls. With adequate manpower a high production rate can be easily achieved. All parts are of sturdy construction to ensure the machine will give a long and trouble free performance.

The Unimark auger screw pump has been developed to give precise flow to our extrusion shoes. The pump is enclosed in an oil jacket and driven by a variable hydraulic motor system. The benefit is constant width and thickness, with excellent start and cut-off to extruded lines. The Unimark pump can be fitted to all of our thermoplastic machine range.   Unimark operates on policy of continual research and development, therefore specifications can change without notice. The images are indicative.

The Unimark Unidrive is a sit-on self-propulsion machine to drive hand-push road marking trollies. The Unidrive is connected to the trolley by a ball and hitch system, so even speed humps are no problem. Powered by a propane fuel Kohler 6hp engine which drives a forward and reverse hydrostatic pump to two high torque hydraulic motors. The seated position makes steering a simple operation and is kinder to the operator. Speed is infinitely variable. The Unidrive can also be fitted with an air compressor for use with the hand-propelled rib machine to give air on demand, eliminating the need for a compressed air cylinder.

We are offering truck drying. All compressed air drying equipment can be fitted to support trucks and marking machines. Supply is from mounted single tool compressor and propane gas. Pneumatic in-cab lift of dryer and ignition system are supplied with kit.

Sugarcane planting is tedious & time consuming. Tractor drawn sugarcane planter performs jobs of Furrow opening, Sett cutting, Seed treatment, Fertilizer Application, Sett Placement and Compaction all in one pass reducing time and labor cost. The one row sugarcane planter consists of cutter Box, Fungicide tank, fertilizer box, furrow closing shovels and compaction roller. The whole seed canes are stacked on the machine. Knives are fixed on the counter rotating rollers which are driven by the tractor power take off shaft. The canes are cut into setts of pre-determined length. The cut setts fall in the middle of the furrow. The setts are then covered with soil by the shovels provided at the back of the machine and compacted by the roller.

Road marking machine an economical solution to small patching or raised profiles. It is bucket-fed and used similarly to a hand mold. Weighing only 50kg, the machine is light enough to load onto a truck. Application is by hand control and sight bar. The unit is supplied with a glass bead dispenser and can also be automated in a manner similar to the hand-propelled line machine.

We are offering powermaster 220 thermoplastic spray extrusion machine.

We are offering powermaster 220 thermoplastic extrusion machine. The powermaster 220 is the next generation of the powermaster 180 machine. The machine had the addition of a 4th wheel, a larger tank capacity and a more powerful 2-cylinder engine making the machine easy to cope with double line and wider line systems. Built to last simple to use and well priced making it a sound investment.

We are offering thermoplastic spray machine.the powermaster 180 thermoplastic spray machine offers an economical solution to small to medium lining works. Again like the powermaster 180 extrusion machine this machine is very maneuverable making it an excellent choice for inner city working.

Voltage : 12

Condition : New

Automatic Grade : Automatic

The powermaster 180 is the smallest ride-on thermoplastic extrusion machine available. A fully automatic machine for road marking with many work possibilities. Small jobs are easy as the material can be mixed and melted in the tank. Medium to large jobs can be accomplished with the use of suitable preheaters. Very maneuverable makes city work simple. Well built and with features found on larger machines makes the road marking machine a very worthwhile investment.

We are offering powermaster 180 cold airless paint machine. Constructed on the reliable and robust powermaster chassis the cold paint airless version is a very economical choice. Highly maneuverable yet large capacity gives the machine the versatility of small city works to major road projects. As an example one contractor applied in excess of 1 million linear meters of lining in a 6 month period thus amortising the purchase in one contract. The option of 3 spray guns also makes the machine suitable for airport runway markings. As with all unimark equipment there are no complicated controls making it very user friendly and very reliable.

Unimark machines are controlled by our 11-programme line/gap computer. The unit gives control to manual, semi- or fully-automatic line laying. The built-in totaliser gives production rates. With 4-position joystick control, line patterns can be altered without stopping the vehicle. Tandem gun operation is also available.   Unimark operates on policy of continual research and development, therefore specifications can change without notice. The images are indicative.

We are offering hymix horizontal preheater. Unimark horizontal preheaters are available as direct flame or indirect oil jacket heated. Sizes range from single 270 liter to 1000 liter and can be twined for extra capacity. 12 v dc electronic gas burner system or 12 v dc diesel oil burner for rapid heat up time. Tanks are fabricated from extra thick boiler plate to avoid any distortion. Mainly used for anti-skid thermoplastic but can be used for high volume road marking thermoplastic or bitumen works. The powerful hydraulic agitators will mix and melt the heaviest of materials efficiently.